Strong SRT 6125 (6155, 6355) Emu Опции

[Admin]

All about patches for Strong SRT 6xx5 only here (manuals, troubles, download links).

Soft upload is here - http://upl.frocus.net/index.php?lng=en&p=4

Manual - http://www.frocus.net/main.php?lng=en&...tatii&pag=7

[Гость__*]

Hi, please where can I found the upload zone? I don't understand russian language?

thank's

[Admin]

DOWNLOADS SECTION: http://upl.frocus.net

[Гость__*]

Hello,
I saw in the creenshot the strong 6xx5 patch replaces the design of the interface. Can I change the color or make the menu items rounded not square?

[Гость__*]

Please tell me if I can keep the original design of the menus after I apply the patch.
thanks.

[Frocus]

Please tell me if I can keep the original design of the menus after I apply the patch.
thanks.

No, you can't change OSD.

[Frocus]

All about patched firmware that emulate Viaccess 2.3, NagraVision, Seca, Irdeto and Conax on receiver Strong SRT SRT 6125 (6155, 6355)
(unfinished article based on original "loading steps.txt").

Introduction. Strong SRT 6125 (6155) it is a receiver for reception of free (FTA) satellite channels. But were found so-called crackers which have changed the initial soft (firmware) sewed up in a receiver, that it could decode the channels crypted in Viaccess 2.3, NagraVision, Seca, Conax and Irdeto (without a card of conditional access, without a user's payment). It was required to update in time only keys for these cryptings.

To download the emulator (patch) in a receiver will be necessary:

1. receiver Strong SRT 6125 (6155, 6355) - 1 piece.
2. computer - 1 piece.
3. serial cable - 1 piece.
4. programmes:
BootLoader.exe
ApplicationLoader.exe
PatchLoader.exe
5. patches and firmwares:
srt61x5fta.urt (or srt6355ci.urt for a Strong 6355)
keys.bin
patch.bin

All soft you can find into: "srt 6xxx loaders.zip", "srt 61x5 patch.zip", "srt 61x5 patch [9-12-04].zip" and other packages.

TO PATCH AN VIRGIN SRT6xxx RECEIVER YOU MUST FOLLOW THIS STEPS:

1. Connect the PC and the SRT6xxx using a null-modem serial cable. Follow the route [ Menu Key -> Installation -> (Enter your securuty code, by default 0000) -> System Set-Up -> System Information ] such that the firmware version is shown.

2. Unplug the receiver, press CH-DWN and keep it until you plug in again the receiver.

3. Run BootLoader and perform CONNECT , this will replace the original boot.

4. Perform again step 2 and run ApplicationLoader, load the application (6xxx.urt) and upload the application.

5. Perform again step 2 and run PatchLoader , load the patch (*patch*.bin) and upload the patch.

6. Perform again step 2 and run PatchLoader, load the keys (keys.bin) and upload the keys table.

7. Start the receiver normally.

8. The online key tool will be used to view the keys present or the user will be able to add or delete his own key.

a) Follow the route [ Menu Key -> Installation -> (Enter your securuty code, by default 0000) -> System Set-Up -> System Information ] such that the firmware version is shown.

Remaining there please Press the following keys in sequence
1. KEY_4
2. KEY_2
3. KEY_2
3. KEY_5
.
So the sequence "4225" will invoke the WeakSoft Editor for further use.

c) Follow the instructions given at the bottom of the menu to proceed further.

Frocus (december, 13 2004)

Updated 11.01.2005

[Гость__*]

Thanks Frocus.

I presume the OSD design was changed because of the limited space on the receiver but if thats not the case can you guys leave the default design on?

Also a bit off-topic, is there a similar patch for 'worldsat discovery 520' receiver?

[Frocus]

Thanks Frocus.

I presume the OSD design was changed because of the limited space on the receiver but if thats not the case can you guys leave the default design on?

You can ask developers about this trouble: www.prosat.ro

[Гость_ed_*]

Hello,

How can i back to the original SRT6125 software? :?:

greetings ed

[Гость__*]

How can I go back to 6355 software ?

[Frocus]

How can I go back to 6355 software ?

You can't

[Гость__*]

Even with J-tag ?

[Frocus]

Even with J-tag ?

May Be...

[Гость_New_*]

Where is this file?

[Frocus]

Where is this file?

http://www.rdi-sat.com/uploadshow.php?id=13

[Гость_New_*]

Thanks so match.

[Гость_lionginass_*]

hey i am gonna to patch my strong srt 6155, bet i have some question: how does the serial cable looks like? cuold anyone show a photo from images.google.lt o smth?
and while reading instruction how to patch the receiver i dont understand what does this sentence means: "Follow the instructions given at the bottom of the menu to proceed further" what menu, and what instructions???

[Frocus]

My Serial Cable (9 to 9 pins):




You can buy serial cable like this from computers shop.

[Гость_kedilo_*]

i have hooked up the cable from my pc to the receiver...but when i do that a green light is blinking and i't won't go on..
and when i hook up the cable i get several times shocked by the electricity

what is te problem with my receiver :? :? :? :?'


and what does this mean 2. Unplug the receiver, press CH-DWN and keep it until you plug in again the receiver.???? must i unplug it from the electricity or the satellite????

[Frocus]

and what does this mean 2. Unplug the receiver, press CH-DWN and keep it until you plug in again the receiver.???? must i unplug it from the electricity or the satellite????

it's mean that you must to unplug receiver from the electricity, then you need to press button CHANNEL-DOWN (on frontal panel) and keep it until plug in again the receiver.

[Гость_jonesdjat_*]

Hi Frocus.
This this is the steps I used to clone my receiver. I had a hard time from the begging but things started working later on. My problem is that after keying in the nargravision keys for sabc, I still received scramble info. Is it the patch or what. Please help. Thanks.

[Гость_jonesdjat_*]

hi, frocus,
Sorry for sending you this information late. I went back to check the key file and install another one and it worked. The software realy works. Thank you so much. Now can i upgrade the firmware of my clone srt-6155 without it affecting the patchig?

[Гость_umtsptz_*]

Hi !!
i cant change BootLoader !!


| Loader Configuration Settings |
---------------------------------------------
Loader Software Version = 4.6.7ps (HW MjrVer-4)
Loader Configured for 1 x 16 Mbit flash
Target Flash MCode = 0x 200020
Target Flash DCode = 0x22C422C4
Loader supports Box To Box Copy
Loader allows same version to download
---------------------------------------------
Download from UART demanded ...
Old Urt Format is not supported

umtsptz

[Гость_Lord348_8_*]

DOWNLOADS SECTION: http://www.freemail.atlastelecom.ro/~gvadi...loads&pag=2

Dear Admin,

I am strongly looking for patch for SRT6155 ...your link doesn`t work ( error : for bidden )....please help me to find a good refrence for download latest patches for this model.

Rgards

.

[Frocus]

I am strongly looking for patch for SRT6155

http://upl.frocus.net/index.php?lng=en&p=4

[Гость_Lord348_8_*]

I am strongly looking for patch for SRT6155

http://upl.frocus.net/index.php?lng=en&p=4

Questions :

1. Can I use patch for 6xxx for 6155 ?

2. Where can I download latest patches for SRT 8100 ?


Regards

.

[Гость_rough raider_*]

Hi!!!
i have little prob ,i cant make to enter TPS aes key in the 6355,can you help me ? i enter keyeditor find TPS 007c00 and there is
par
par
0c
0d
0e
etc ...
I tryed to add new lines ,delete old ones , change old ones but no result
should i change something in two par lines

with other chanels there is no problem

[Frocus]

rough raider, is not so easy. To watch TPS is needed to get patch vers.0.3, then open this patch with HexEditor and fixing TPS AES HUSH...

[Гость_rough raider_*]

Thnks ! Ill try when I get little time

[Гость_migines_*]

salu2

[Гость_miki_*]

i have strong 6130.did someone knows whe are i can upload emu for premier and key.help me please

[Гость_rough raider_*]

can anyone tell me is it possible to make connection between srt 6xxx and PC that alowes you to live update ke*s without turning off receiver ?
is it technical possible ?

[Frocus]

rough raider, when I update keys into tuner - I connect PC and SRT in hot, I don't disable PC or receiver. But is not recommended to do same.

[Гость_rough raider_*]

Tnks ! you helped me a lot

[Гость_nnorte_*]

Hello. Pleaaaase help me.

I have a 6125 and tryed to patch it. I followed every step from the tutorial. Everything went apparently ok until the end. All the files were uploaded and the receiver also has the new interface.

But, when I press the 4225 sequence in System Information, nothing happens.

Firmware 2.07 Nov 28 2006
Bootstrap 4.6.7ps

I used the Weaksoft 1.8.0zip package, and all other software from upload section.

Did anyone have a similar problem or knows the way to fix it.

Thanks

[Frocus]

It's OK. Now you need to upload into receiver thr patch version-2.00 and keys-2.00. Then you will have possibility to open menu 4225.

[Гость__Chefk0ch_*]

Hi @all,

same problem here, Srt6125

Software & Howto taken from Nachtfalkes Site, seems similiar to your site.

System information now looks like this:


Do i have to use the "4225" Menu in the box, i thought just uploading key file and then all went fine. But nothing happens, all scrambled Programs are still scrambled...
The 4225 menu opens correctly btw

Where did i go wrong?

[Гость_Enes_Garaga_*]

@ Chefk0ch upload patch ver 1.00 you can find patch in upload section url is
http://upl.frocus.net/index.php?lng=en&get_id=1040
upload patch with patch loader(weaksoft v 1.6.0.) then upload latest keys for patch ver 1.00 from this url :
http://upl.frocus.net/index.php?lng=en&get_id=1044

that shal solve the problem

[Гость__Chefk0ch_*]

Thx Enes_Garaga,

got it by myself meanwhile.

Do i have to update the keys every day?
Because now austrian tv is dark, taken the key file from today...

Or is it just a bad time to start with this things?

btw, ist really hard to register to this forum if you cant read russian...

btw 2
As seen today, great service, that you made here guys, really fast!
Thx a lot!

Chefk0ch

[Гость_Sholomo_*]

Hello
I have some questions.
is this site: http://upl.frocus.net/dnld/strong6xxx/loading%20steps.txt
still actual for 6155 ?

2nd: I dont understand the point 7, do i need to re-press CH-DOWN before i am turning on receiver or after i turn it on??

3rd: After point 4 is done. Do i need to go to point 7 and first turn on receiver and then go back to number 2???
Or when I am done with point 2 I dont need to turn on the receiver but just start with point 3?


What is actually the meaning of AKEYS and HKEYS?
Can I load keys before I patch my receiver?

Is it important which patches do I upload and in which order?
What about keys do I need to upload only the latest or also some older?

Boot/patch/application loaders on the upload site are still "up to date" ?

Can you give me some sites or key words where i will find answers of those questions.

[Гость_pbabic_*]

Where SW to Croatia language MENU...